CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

October 27, 2019   |   by admin

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Daijind JoJodal
Country: South Sudan
Language: English (Spanish)
Genre: Photos
Published (Last): 5 April 2011
Pages: 476
PDF File Size: 3.60 Mb
ePub File Size: 20.48 Mb
ISBN: 966-1-88437-411-3
Downloads: 10880
Price: Free* [*Free Regsitration Required]
Uploader: Goltihn

This is because all VLANs are running spanning tree with the default behavior.

CCNP SWITCH Lab Manual, 2nd Edition

It cannot be used with channel-group number mode on command. The ports and port channel can be re-enabled after the EtherChannel is configured. Use the show interfaces trunk command on all switches to verify the trunks. By default, how many lines are available for Telnet on the access switches?

Display the spanning tree information for DLS2 again. If the sender port priorities are the same, the switch picks the port that receives BPDUs with the lowest sender port number. Implementing broadcast storm protection on trunk interfaces can help prevent this. For comparison, issue the show spanning-tree command on DLS1. Change DLS1 to be the primary root switch.

If lists are not defined, a default list is used.

This allows the link to the router to rapidly transition to the forwarding state despite being a trunk. Notice the use manuak a static default route.

  GERILLA PAZARLAMA PDF

Port assignment to a VLAN is an interface configuration operation.

HSRP provides a transparent failover mechanism to the end stations on the network. This means that when the ping was getting routed, there was some point where a router did not have a route to the destination or that the packets were getting dropped for example, through an access list.

The following is sample output from ALS1. If this line is not added, an implicit deny catches all other traffic and denies it.

Was this ping successful? Based on the various design considerations, you can choose UDLD or the loop guard feature or both. The default VTP mode is server for both switches.

In the previous steps, you configured EtherChannels as Layer 2 trunk connections between switches. This configuration uses fac, which is made up of the following: In most cases, you must manually configure the spanning-tree root to ensure optimized paths throughout the Layer mahual network.

The functioning switch will take over as the default gateway to provide virtually uninterrupted connectivity for hosts at the access layer. Configure VTP on the switches.

Next, the aaa authentication dot1x default local command is replaced with either the aaa authentication dot1x default group radius command or the aaa authentication dot1x default group radius local command. On the logical interface, issue the no switchport command to make it a Layer 3 port.

ccnp-switch-instructor-lab-manual-slm

In privileged EXEC mode, type delete vlan. D – down P – in port-channel I – stand-alone s – suspended H – Hot-standby LACP only R – Layer3 S – Layer2 U – in use f – failed to allocate aggregator u – unsuitable for bundling w – waiting to be aggregated d – default port Number of channel-groups in use: VTP server is the default mode.

  CANAVOS ESTADISTICA PDF

Share a link to All Resources. Click here to sign up. The distribution layer switches are Layer 3 devices and do not need default gateways.

Display mxnual spanning tree information for all switches. There is no danger of creating a spanning tree loop because you are not connecting another switch. HSRP negotiates and determines which switch accepts information forwarded to the virtual gateway IP address.

When you get back to the office, you meet with your boss to discuss your concerns. If you’re interested in creating a cost-saving package for your students, contact your Pearson rep.

Commands used in this. After the access list has been applied verify the configuration in one of the following ways. Management Interface IP Address: The priority number of a VLAN can be between 0 and in mznual of DLS2 debug spanning-tree events Spanning Tree event debugging is on b. Verify the swiych QoS configuration at the access layer using the show mls qos interface interface-type interface-number and show run commands.