ASTM A384 PDF

October 3, 2019   |   by admin

This standard is issued under the fixed designation A/AM; the number 1 This practice is under the jurisdiction of ASTM Committee A05 on Metallic-. In all cases only the current version of the standard as published by ASTM is to be considered the official document. Designation: A – 76 (Reapproved ) . ASTM A – A M – 02 – Download as PDF File .pdf), Text File .txt) or read online.

Author: Goltitaur Akinoll
Country: China
Language: English (Spanish)
Genre: Education
Published (Last): 1 December 2017
Pages: 142
PDF File Size: 17.13 Mb
ePub File Size: 4.36 Mb
ISBN: 127-2-59741-931-4
Downloads: 74030
Price: Free* [*Free Regsitration Required]
Uploader: Gardagis

This is not asfm of an I-beam, pipe, H-column, or any other section that is symmetrical about both its major axes. In the case of sheet metal, the product which has a right-angle bend in the sheet metal itself will remain flatter and be freer from distortion if the radius of the bend is as large s384 practicable.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

ASTM A _图文_百度文库

Furthermore, cylindrical structures are less likely to warp or distort than rectangular or elliptical ones. I the f frame has to be dipped one half at a time, it will be better to have the sheets galvanized, rolled flat after galvanizing, and assembled to the galvanized frame by the use of aluminum alloy or galvanized rivets.

Steel invariably contains internal stresses induced at the mill from rolling operations used to bring structures, plate, and sheet to the final thickness. Historical Version s – view previous versions of standard. Necessary precautions to fabricate properly and prepare the material for galvanizing to prevent embrittlement are described in Practice A ASTM does not give any warranty express or implied or make a834 representation that the contents of this abstract are accurate, complete astn up to date.

Factors in Warpage and Distortion 3. When two steels of different thicknesses are assembled and brought up to galvanizing temperature, the thinner steel heats up and expands more quickly than the thicker steel. Originally published as A – 55 T. This abstract is a brief summary of the referenced standard.

A – 76 Reapproved Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies’ This standard is issued under the fixed designation Satm ; the number immediately foliowing the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

Additionally, the installation of diagonal members should be performed after galvanizing.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Practice ASTM A provides guidance on safeguarding against warpage and distortion for optimum hot-dip galvanizing and shall be complied with in both design and fabrication.

  GANN SIGNS TITLE-BIBLE-TETRAGRAMS PDF

The following can cause warpage and distortion: Inch pounds and SI units are not necessarily exact equivalents. Suggested corrections for panel fabrication are detailed. This specification deals with safeguarding against warpage and distortion during hot-dip galvanizing of steel assemblies. Optimize Welding Before Hot-Dip Galvanizing Welding results in significant residual stress in small areas of an assembly due to the extreme temperature differences experienced.

These rivets can be countersunk or flat head if aa384 protruding head of the ordinary button or round head rivet is objectionable. After galvanizing, these products should be air cooled instead of quenched to minimize induced stress from the cooling cycle. Last previous edition A – If the angie steel frame and sheets are punched prior to galvanizing the recommended procedurethe use of drift pins asmt bring the holes into alignment should be avoided as far as possible at the time the sheets and frame are assembled.

Avoid Susceptible Thin Sheet Steels Steel invariably contains internal stresses induced at the mill from rolling operations used to bring structures, plate, and sheet to the final thickness. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Clamps may be applied to prevent shifting or movement during the welding operation. A superscript epsilon E indicates an editorial change since the last revision or reapproval.

ASTM A384 Recommendations

All efforts should be made to keep the stresses in the construction as low as possible right from the beginning to enable the steel to absorb the internal stresses completely. Thls stendard Is subject to revision at any tlme by the responsible technical commHtee and must be reviewed every five years and H not revised, either reapproved or withdrawn.

It is recommended that welding procedures be carried out in conformancewith the pertinent specificationsof the American Welding Society. Suggested Corrections for Panel Fabrication 4. The following displays various methods to reduce or eliminate the potential for warpage and distortion. Channels and other nonsymmetrical sections should be avoided for the framework of a sheet metal assembly that is to be hot-dip galvanized whenever it is possible to use symmetrical shapes or sections.

Welding results in significant residual stress in small areas of an assembly due to the extreme temperature differences experienced. Link to Active This link will always route to the current Active version of the standard.

Oftentimes sheet or plate can be returned to a flattened state using a jig or by weighing the product down on a flat surface during the cool-down. Specify symmetrically rolled sections instead z384 angle or channel frames. In welding any intermediate lengths along one side of a common member, care should be taken to prevent warpage of the common member due to the application of high heat x384 the same side at various intervals along its length. Within the text of this specification and where appropriate, SI units are shown in parentheses.

  DE PERLAS Y CICATRICES PEDRO LEMEBEL PDF

Where excessive cold working or tight bend radii cannot be avoided, the product should be stress relieved per the guidelines provided within ASTM A, Section 6. Where welding before galvanizing cannot be avoided, the internal stresses in the connections asmt be minimized by avoiding joint designs or weld lengths which are greater than statically required, and by placing ast near to and symmetrically around the neutral axis – aligning welds so that shrinkage and opposing forces are balanced rather than all asstm in the same direction.

Wherever possible, galvanize thick and thin portions separately and join them after galvanizing. Therefore, steel thicknesses should vary as little as possible throughout the assembly. The overall amount of welding can be minimized by using bolted connections or performing assembly after hot-dip galvanizing. Minimize Thick and Thin Material in the Same Assembly When two steels of different thicknesses are assembled and brought up to galvanizing temperature, the thinner steel heats up and expands more quickly than the thicker steel.

Common distorted and warped members of wstm are sheets or plates assembled by welding or riveting.

ASTM A Recommendations | American Galvanizer’s Association

This will prevent the rusting of the surfaces which are so connected that molten zinc cannot circulate through the crevices to galvanize the contacting surfaces. Symmetrical sections such as I-beams and tubing will be less likely to distort than asymmetrical pieces camber beams, channels, tees, custom beams, girders because the thermal expansion forces above and below the natural axes balance each other.

The design and fabrication of the product to be galvanized are the responsibilities of the designer and the fabricator. Current edition approved Oct. In nearly every case, regardless of size, channels require straightening after galvanizing. A number in parentheses indicates the year of last reapproval. Asymmetrical Design Symmetrical sections such as I-beams and tubing will be less likely to distort than asymmetrical pieces camber beams, channels, tees, custom beams, girders because the thermal expansion forces astk and below the natural axes balance each other.